廚房排煙罩在安裝過程中一定要注意機體水平，安裝完后觀察其水平度，避免傾斜。確保廚房排煙罩無晃動或脫鉤現象。

　　The kitchen exhaust hood must pay attention to the level of the body during the installation process, and observe its level after installation, so as to avoid the tilt. Ensure that there is no sloshing or decoupling in the kitchen exhaust hood.

　　廚房排煙罩在安裝前一定要確定打孔部位沒有不水管，煤氣管，電線經過，以免造成破壞，甚引發觸電危險等。

　　Before the installation of kitchen exhaust hood, we must make sure that the location of perforation is not without water pipes, gas pipes and wires passing through, so as not to cause damage or even cause electric shock.

　　若排煙到共用煙道，勿將排煙管插入過深導致排煙阻力增大。若是通向室外，則務必使排煙管口伸出3cm。排煙管不宜太長，好不要超過2米，而且盡量減少折彎，避免多個90度折彎，否則會影響吸油煙效果。

　　If the smoke to the common flue, do not insert the smoke pipe too deep to increase the resistance to smoke. If it leads to the outside, be sure to extend the 3cm of the exhaust pipe. The exhaust pipe should not be too long, it is best not to exceed 2 meters, and reduce the bending as far as possible, avoid multiple 90 degrees bending, otherwise it will affect the effect of oil absorption.

　　抽廚房排煙罩安裝完成后，一定要記得調試廚房排煙罩。一般是通過功能鍵的開關，看是否運作正常。

　　When the kitchen smoke hood is completed, be sure to remember to debug the kitchen exhaust hood. Generally, it is through the switch of the function key to see if it works properly.

　　(1)當風管與風機連接時，應在進出風口處加軟接頭，其軟接頭的斷面尺寸應與風機進出風口一致。軟管接頭一般可采用帆布、人造革等材料，軟管長度不宜小于200，松緊度應適宜，柔性軟管可緩沖風機的振動。

　　(1) when the wind pipe is connected with the fan, the soft joint should be added at the inlet and outlet. The section size of the soft joint should be the same as the fan inlet and outlet. Hose joints usually use canvas, artificial leather and other materials, the length of the hose should not be less than 200, the tightness should be suitable, flexible hose can buffer the vibration of the fan.

　　(2)對輸送易燃、易爆氣體的鋼板風道，在風道連接法蘭處應安裝跨接線，并與靜電接地網連接。

　　(2) the cross wiring should be installed at the flange of the air duct connecting to the flammable and explosive gas, which is connected with the electrostatic grounding grid.

　　(3)當風道與除塵設備、加熱設備等連接前，應待設備安裝完畢后，按實際測繪的圖紙進行預制和安裝。

　　(3) before the wind tunnel is connected to the dust removal equipment and heating equipment, the equipment should be prefabricated and installed according to the actual drawings.

　　(4)當水平風道高度在4m以上時，安裝人員應系帶。腳手架或移動式支架上的跳板應固定好，跳板寬度應符合規范，在腳手架上的安裝人員宜攜工具袋，防止工具或電鉆等物墜落傷人。

　　(4) when the height of the horizontal air duct is above 4m, the installation staff should be a seat belt. The springboard on scaffold or mobile bracket should be fixed. The springboard width should conform to safety regulations. The installation personnel on scaffolding should carry tool bags to prevent falling tools or electric drills from hurting people.

　　(5)風道安裝時，進、出風日宜在風道預制時開出洞口，如需在安裝完畢的風道上現開風口，其接口處應嚴密。

　　(5) air duct installation, into and out of the open hole in the air duct should be prefabricated, if installed in the air duct on the open air, the interface should be tight.

　　本文的精彩內容來自濟南排煙罩詳細內容請點擊我們的網站:http://www.pvcbox.cn/謝謝您的到來!

　　The wonderful content of this article comes from the detailed content of the Ji'nan smoke mask. Please click on our official website: http://www.pvcbox.cn/ thank you for your arrival.

上一篇：在通風管道的迎風側安裝防火閥的好處
下一篇：建筑工程施工中對通風管道的排布技巧